Performance Parts News

Flowmaster Exhaust for 1967-1970 Mustangs

todom — Tue, 20 Nov 2007 13:54:47 +0000

Flowmaster just released two exhaust systems for the 1967-1970 Mustang. Both kits are designed for Mustang V8s equipped with full length headers. The Flowmaster 17281 has been engineered for Mustangs with rear valance cutouts, exiting at the factory valance location with a pair of 3″ rolled edge Flowmaster embossed stainless tips. Exhaust system Flowmaster 17282 offers a virtually identical exhaust system built for cars without rear valance cutout, with tailpipes, not tips, exiting at the stock location. Both systems feature Flowmasters famous Super 44 mufflers that are tuned for classic Flowmaster American Thunder sound and improved exhaust gas flow.

flowmaster, muffler, mustang, New exhaust, New Performance Parts

Lakewood Introduces Hemi Bellhousing 15315

todom — Mon, 19 Nov 2007 14:54:07 +0000

Lakewood Industries now offers part number Lakewood 15315, a SFI approved safety bellhousing for the 5.7L Hemi as 273-360 V8 engines. Designed to accept the popular tremec TKO 500/600 series 5-speed transmission. Lakewood supplies the SFI 6.1 rated bellhousing, safety block plate and all necessary mounting fasteners. The SFI specification applies to containment bellhousings for use with SFI 1.1 and 1.2 single and dual disc clutches assemblies for naturally aspirated vehicles.

General, New Performance Parts

TCI® 700R4 Constant Pressure Valve Body 376020

todom — Mon, 17 Sep 2007 14:32:18 +0000

Revolutionary TCI® Constant Pressure Valve Body TCI 376020 avoids incorrect T.V. cable
installation - the most common cause of GM 700R4 transmission failure
Many racers and street performance enthusiasts incorrectly install their transmission with the critical T.V. cable used to set internal line pressure and part throttle shifting either left
disconnected or improperly adjusted. The result – total transmission melt down often
within a matter of a few miles. The TCI® 700R4 Constant Pressure Valve avoids all
those problems.
In the past, the T.V. cable adjustment on GM 700R4 transmissions required near-expert
mechanical abilities. Installation of the TCI® 700R4 Constant Pressure Valve Body
avoids common transmission destruction by maintaining at least 200psi line pressure at
all times. While the T.V. cable still needs connection for proper transmission operation,
the TCI® 700R4 Constant Pressure Valve provides more freedom when setting part
throttle shift points. Line pressure is fixed with no chance of encountering a low line
pressure condition.

constant pressure valve, New Performance Parts, TCI, transmission

Hypertech 41048 Power Programmer For Ford Mustang GT 4.6L

jlmitra — Thu, 13 Sep 2007 14:02:09 +0000

Hypertech is making their Power Programmer available for the 2005-2007 4.6L Ford Mustang GT, offering 22 optimized tuning programs, regular and premium fuel tuning for the stock air intake and for each of the 10 most popular Cold Air Intake Kits. Now you can have perfect air/fuel mixtures and spark advance no matter which air intake you have on your vehicle!

Additional features include: adjustable shifts points and firmness, adjustable tire and gear, adjustable rev limiter and top speed limiter, adjustable fans and Read & Clears factory DTCs.

HYPERTECH 41048 POWER PROGRAMMER FOR FORD MUSTANG GT 4.6L

See other Hypertech products.

4.6L, ford, General, hypertech, mustang, New Performance Parts, New programmers and chips, programmer

Professional Products Intake Adapter Kit for FORD 5.4L

todom — Mon, 30 Jul 2007 14:48:26 +0000

Ford’s 5.4L is becoming the performance choice for many performance Mustang builders, replacing the 4.6L engine as the larger displacement provides more power, but without a performance intake manifold the transplant is one step short. Professional Products has introduced a solution with its Professional Products 54110 4.6L to 5.4L Adapter Kit for Ford. This kit allows the installation of Professional Products 4.6L 2-valve Intake Manifold Professional Products 54060 -Satin finish or Professional Products 54061-polished, or any other 4.6L 2V manifold, to the 5.4L engine without additional modifications. The kit includes the two aluminum adapter plates, intake gaskets and all the necessary mounting hardware to help your Mustang breathe free and produce more power.

See PerformanceParts.com for more Professional Products parts.

General, Intake Manifolds, New manifold, New Performance Parts, professional products

New Superchips 1846 Tirepaq for Ford

todom — Thu, 21 Jun 2007 18:27:54 +0000

Superchips introduces their newest product, Tirepaq for Ford applications, Superchips 1846. This amazing device works just like the Superchips FlashPaq. It plugs into the vehicle OBDII port and allows the user to recalibrate his/her speedometer for larger or smaller tire sizes or gear swaps. The Ford FlashPaq 1846 for Ford gas trucks and SUVs and Ford diesel trucks also calibrates for tires from 26″ to 38″ and a wide range of gear ratios including 3.08, 3.31, 3.55, 3.73, 4.10, 4.30, 4.56, 4.88, and 5.13. TirePaqs for GM diesel trucks and Dodge vehicles will be released soon. The Tirepaq can also be used as a scan tool that can read and clear diagnostic trouble codes (DTCs or “check engine” lights). Tirepaq will tune your shifting to compensate for those tire and gear changes to keep your ride driving smoothly.

diesel, ford, ford truck, New Performance Parts, New programmers and chips, SuperChips

12% HORSEPOWER GAIN WITH PROFORM CARB SPACER

todom — Thu, 21 Jun 2007 11:53:29 +0000

Recent dyno testing at Adrenaline Autosports, in Chatsworth, CA, on a mildly built Ford 302, fitted with stock 289 heads, revealed incredible results. Baseline numbers with a 600-cfm Holley carb and no spacer produced 218.57 rear wheel horsepower at 5500 rpm with 252.97 ft-lbs. of torque. The carb was switched to a 680-cfm QFT street carb, manufactured with a Proform® carb main body, and one pull was made with each of the three variations of Proform 1-inch phenolic spacers supplied in their Trackside Carb Spacer kit.
The wide open spacer proved to be the most efficient for this engine, producing a whopping 244.62 rear wheel horsepower with 276.55 ft-lbs. of torque, equating to a 12% HP increase and , a 9% torque increase. That’s a gain of 26.5 horsepower and 23.58 ft-lbs. of torque with only a carb change and spacer install. We broke down the numbers for the spacer only, and this simple change resulted in an increase of 14 rear wheel horsepower and 9 ft-lbs. of torque. Incredible! and the 3-in-1 spacer kit is under $80. Now that’s a low cost power adder producing astounding results!

By simply changing the carb and adding the Proform 67160C spacer to this engine, we gained increased throttle response, realized the full power band of the engine, and at wide open throttle it felt like it would never stop pulling. That, coupled with the horsepower and torque increase, makes this combination a winner on street or strip.

carburetor, General

Add Hurst Performance To Your Car With The 5010002 3-Speed Indy Shifter

almartin01 — Wed, 25 Apr 2007 17:32:40 +0000

The Hurst Indy 3-speed shifters are designed to fit most popular passenger cars with 3-speed manual transmissions. These shifters are excellent for converting column shifters or for replacing floor shifters. They sport an attractive chrome-plated stick and gate, and come with all hardware and instructions.

• Spring loaded gate for ease of operation
• Short precise throws for less stick travel
• Attractive chrome-plated stick (3/8-24 thread) can be adjusted to many positions
• Excellent for replacing floor shifter or for conversion column shifter
• Fits most popular passenger cars with 3-speed manual transmissions
• All components are plated for protection
• Complete with shifter boot, hardware and easy-to-follow installation guide

Hurst 5010002 3 Speed Shifter Indy SSA Universal

For more information, including other Hurst products, visit the Hurst page at performanceparts.com.

3 speed transmission, column shift conversions, how to, hurst, indy, New Performance Parts, New shifter, New shifters, passenger car, performance enthusiast, performance parts, performanceparts, racing, shifters

Superchips TIREPAQ 2816 Speedometer Correction Device For ‘96-’07 GM Trucks & SUVs

almartin01 — Tue, 24 Apr 2007 19:49:37 +0000

Superchips proudly introduces the Tirepaq (Superchips 2816) for 1996-2007 gas-powered GM V8 trucks and SUVs. Superchip’s Tirepaq corrects your vehicle’s speedometer readings electronically to compensate for non-factory wheels, tires and rear-end gear swaps. It also intuitively adjusts shift patterns to improve drivability when aftermarket wheels, tires and gears are installed. Superchips Tirepaq unit will never be out-of-date because you can update your Tirepaq on the internet!

Superchips Tirepaq programmer can also be used to retrieve and clear annoying “check engine” lights. The Tirepaq programmer can also be upgraded (at an additional cost) to become the Superchips Flashpaq performance programmer.

SUPERCHIPS TIREPAQ 2816 SPEEDOMETER CORRECTION DEVICE

For more information, including other Superchips products, visit the Superchips page at performanceparts.com.

General, general motors, gm, horsepower, how to, New Performance Parts, New programmers and chips, performance enthusiast, performance parts, performanceparts, programmer, programmers and chips, SuperChips

Only The Best! Master Rebuilding Kit Edelbrock 1477 Available

almartin01 — Mon, 23 Apr 2007 20:05:51 +0000

Check out this Master Rebuilding Kit from Edelbrock, featured at performanceparts.com! The best maintenance and replacement parts you can buy for your Edelbrock carburetor come only from Edelbrock. These are the same parts Edelbrock installs at the factory so you know they will fit and work perfectly.

The kit includes parts and gaskets to rebuild any of Edelbrock’s square bore carbs.

Edelbrock 1477 Master Rebuilding Kit

For more information, including other Edelbrock products, visit the Edelbrock page at performanceparts.com.

Air and Fuel, carbs, carburetor, competition, edelbrock, New Carburetor Service Parts, New Performance Parts, performance, performance enthusiast, performanceparts, rebuilding kit, square bore carbs, street rod